Basismaterial:
Kunststoff

Selbstheilend
Die MARTOR-Schneidmatten verfügen über eine selbstheilende Oberfläche. Sie tolerieren auch Schnitte mit schärfsten MARTOR-Klingen und unter höchstem Druck. Anschließend sehen sie wieder aus wie neu.

Mit Rasteraufdruck
Der Rasteraufdruck unterstützt Sie beim exakten Schneiden. Mehr noch: Die Vorderseite ist mit einem cm-Raster versehen, die Rückseite mit einem Inch-Raster. Wählen Sie aus, was Sie benötigen.

Große Auswahl
Die MARTOR-Schneidmatten gibt es in fünf verschiedenen Größen, von sehr groß bis ganz klein. Je nach Anlass und Arbeitsumfeld finden Sie bei MARTOR also immer das passende Format.

• Swedish pattern
• 45° angled jaws
• jaws with offset teeth in opposite direction
• teeth additionally induction-hardened
• I-beam handle design
• captive adjustin g nut
• red powder-coated, jaws bright ground
• Gripping jaws with specially hardened te eth, hardness approx. 56 HRC

• for dismantling round cables exceeding Ø 25.0 mm
• removes all sheaths of standard cab les
• suitable for longitudinal and circular cutting
• cutting depth can be adjusted up to 5.0 mm
• replaceable blade (both sides can be used)

• Universal Tweezers are suitable for demanding standard applications and precision tasks
• Wide range of designs: straight, angled, gripping surfaces and handles smooth or serrated, with needle points, narrow or blunt tips, as well as different lengths
• For the electronics indust ry, watchmakers and jewellers
• High-quality stainless steel: extremely tough and very good co rrosion resistance against a variety of atmospheric environments and many corrosive materials

• precision pliers for ultra fine cutting work, e. g. in electronics and fine mechanics
very precisely ground and sharp cutting edges with very small bevels for exact cutting on delicate electronic components
• also available without bevel for flush cutting
• cutting edges additionally induction-hardened, cutting edge hardness approx. 62 HRC
• approx. 20% lighter t han conventional electronics pliers
• bolted joint with carefully manufactured joint surfaces for even, low-friction movement throughout the entire opening range
• smooth-running double sp ring for a gentle and even opening
• ergonomically optimised multi-component handles
• p ointed head
• with lead catcher - no uncontrolled loss of cut wire ends

• for very tough, continuous use
• high cutting performance with minimum effort due to o ptimum coordination of the cutting edge angle and transmission ratio
• precision cutting edges additionally induction-hardened (cutting edge hardness approx. 64 HRC), for all sorts of wire inclu ding piano wire
• Pliers with integrated, insulated tether attachment point for a tool tether< /li>

Increases your efficiency: Wiha MagicSpring® holding feature holds all Torx® screws in place without a magnet.

Makes handling easier: Always the correct key when you need it.

Saves time: Ensures order: removal and targeted insertion in the holder is child's play.

Product dimensions: 234 x 81 x 34 mm (LxWxD)

Application: Suitable for positioning, fastening and loosening TORX® screws in difficult-to-access spots.

Supplementary information: MagicSpring® from size T6

Quick removal: turn the L-key and pull it out

Nonmagnetic holding feature

It's a common experience. It is not easy to remove individual keys from many L-key holders or place them back in the holder again. With Wiha ErgoStar, you can now say goodbye to such problems as it eliminates the bother in an ingenious way. Turning one L-key in the holder makes all the other keys turn to the side at the same angle, allowing you to remove the key you need quickly and comfortably. A clamping mechanism in the holder makes sure that the keys cannot fall out, regardless of whether the holder is open or closed. Thanks to the MagicSpring® holding feature (from size T6), the L-keys hold all TORX® screws firmly in any position perfectly without any magnets. The set contains thirteen black-oxidised TORX® L-keys in standard sizes. The L-key set can be hung up directly at the workplace using the suspension bracket on the holder.

Content:

• 1x L-keys TORX®, black oxidised T5 x 72 mm (24313)
• 1x L-keys TORX® MagicSpring®, black oxidised T6 x 80 mm (31233)
• 1x L-keys TORX® MagicSpring®, black oxidised T7 x 88 mm (31234)
• 1x L-keys TORX® MagicSpring®, black oxidised T8 x 101 mm (31235)
• 1x L-keys TORX® MagicSpring®, black oxidised T9 x 111 mm (31236)
• 1x L-keys TORX® MagicSpring®, black oxidised T10 x 121 mm (31237)
• 1x L-keys TORX® MagicSpring®, black oxidised T15 x 136 mm (31238)
• 1x L-keys TORX® MagicSpring®, black oxidised T20 x 148 mm (31239)
• 1x L-keys TORX® MagicSpring®, black oxidised T25 x 163 mm (31240)
• 1x L-keys TORX® MagicSpring®, black oxidised T27 x 176 mm (31241)
• 1x L-keys TORX® MagicSpring®, black oxidised T30 x 191 mm (31242)
• 1x L-keys TORX® MagicSpring®, black oxidised T40 x 210 mm (31243)
• 1x L-keys TORX® MagicSpring®, black oxidised T45 x 232 mm (31244)
• 1x ErgoStar holder

Increases your efficiency: Screwdriver handle size concept for optimal balance between precision and control.

Makes handling easier: Extra-long rotating cap ensures optimum feed.

Increases your efficiency: Careful workmanship and controlled power transmission thanks to the slim handle with soft grip.

Product dimensions: 135 x 17 x 17 mm (LxWxD)

The challenge in precision screw fastenings is to work meticulously and carefully without damaging the work piece. Thanks to their long, slim handles and quick-turning zone, Wiha PicoFinish® fine screwdrivers are ideal for delicate and high-precision tasks in precision mechanics as well as for hobbyists and model building. Its ergonomic handle design with a soft zone makes it comfortable to use. The smooth-running rotating cap allows users to turn the screwdriver quickly and sensitively. The printed screwdriver symbols on the rotating cap make it easier to select the right screwdriver profile.