Dreusicke offers the fine tools you will need for the maintenance and repair of office machines, computers, electronic and/or fine-mechanical devices. (for commercial users only)
- high transmission ratio for easy cutting
- requires 50 % less effort compared with con ventional combination pliers due to optimised transmission ratio
- solid construction for heav iest strain
- universally applicable
- ergonomically optimised handle shape for firm co ntact to the hand and fatigue reducing operation
- particularly effective cross-hatched knurle d gripping zone in the jaws - for strong gripping and pulling
- additional gripping zone below the joint for powerful leverage and pressing performance
- with cutting edges for soft and ha rd wire
- cutting edges additionally induction-hardened, cutting edge hardness approx. 62 HRC< /li>
- American style
- with fish tape puller in the joint gap
- with universal mandrel crimping point below the joint
Meets your requirements: Yellow hammer head / medium-hard: e.g. for tool and machine engineering, car repairs, sheet metal and assembly work.
Simplifies your work: Makes work easier, optimum impact effect and less effort needed.
Protects your health: Deadblow Hammering without recoil minimises loads on joints, tendons and muscles.
Application: Ideal for delivering measured positioning blows on components such as work pieces in machine vices or for installation work. Medium-hard hammer heads eminently suitable for tool and machine engineering, car repairs as well as sheet metal and assembly work.
Extra: With cast iron balls inside the hammer head for recoilless work.
Choosing the right hammer is particularly important on sensitive surfaces to prevent damage. With its steel tube handle, the no-recoil soft-faced hammer allows the user to deliver measured positioning blows, protecting delicate surfaces and edges through its high-impact effect. Thanks to the special metal filling in the hammer head, the soft-faced hammer also guarantees absolutely no recoil, thus protecting joints. Around 25% more hammer head mass ensures additional power. The yellow medium-hard hammer faces are ideal for universal use in areas such as tool and machine engineering as well as sheet metal and assembly work. The hammer is also impressive due to its steel tube handle with ergonomic, non-slip grip. Each hammer head is available individually as a spare part.
Increases your efficiency: Wiha LiftUp electric saves 75% volume and 50% less weight for 100 % efficiency.
Protects your health: No risk of injury, all blades stowed safely inside the handle.
Offers you full protection: Each tool individually tested at 10,000 V AC and approved for 1,000 V AC.
Increases your safety: Wiha slimBits ensure good, protected access to deep-set screws.
Application: Suitable for controlled fastening for live parts up to 1,000 V AC, especially for portable use.
Note: Not for use with bit styles C 6.3 and E 6.3.
Clearly arranged and easy to remove
Saves 75% of space
slimBits allow access to low-lying screws thanks to integrated insulation
Expandable and compatible with EVF products
Safe operation up to 1,000 V AC
The screwdriver with the bit magazine LiftUp electric is the ideal companion for every electrician out on a job. The bit depot hidden in the handle provides space for 6 standard slimBits and extends out of the magazine at the press of a button, making it easy to take out the bits. The time-tested ClicFix holder grips all bits securely and reliably locks them into place. This technology transforms the bit magazine into an all-purpose screwdriver. The magazine bit holder also ensures maximum safety. Both the magazine bit holder and the slimBits that it contains are certified to the international IEC 60900 standard. The slender, 75 mm slimBits ensure perfect access to low-lying screws or spring clips thanks to protective insulation fully integrated into bits in the front section. The twistable cap brings a further advantage, ensuring convenient handling.
6 mm slimBits only to be used in the slimVario® bit holder and slimTorque VDE bit holder (VDE torque system).
Manufactured acc. to IEC 60900.
Content:
- 1x slimBit electric bit Slotted 2.5 mm x 75 mm (34578)
- 1x slimBit electric bit Slotted 3.0 mm x 75 mm (34579)
- 1x slimBit electric bit Slotted 4.0 mm x 75 mm (34580)
- 1x slimBit electric bit Slotted 5.5 mm x 75 mm (34581)
- 1x slimBit electric bit Phillips PH1 x 75 mm (34583)
- 1x slimBit electric bit Phillips PH2 x 75 mm (34584)
Increases your efficiency: Wiha LiftUp electric saves 75% volume and 50% less weight for 100 % efficiency.
Protects your health: No risk of injury, all blades stowed safely inside the handle.
Offers you full protection: Each tool individually tested at 10,000 V AC and approved for 1,000 V AC.
Increases your safety: Wiha slimBits ensure good, protected access to deep-set screws.
Application: Suitable for controlled fastening for live parts up to 1,000 V AC, especially for portable use.
Note: Not for use with bit styles C 6.3 and E 6.3.
Clearly arranged and easy to remove
Saves 75% of space
slimBits allow access to low-lying screws thanks to integrated insulation
Expandable and compatible with EVF products
Safe operation up to 1,000 V AC
The screwdriver with the bit magazine LiftUp electric is the ideal companion for every electrician out on a job. The bit depot hidden in the handle provides space for 6 standard slimBits and extends out of the magazine at the press of a button, making it easy to take out the bits. The time-tested ClicFix holder grips all bits securely and reliably locks them into place. This technology transforms the bit magazine into an all-purpose screwdriver. The magazine bit holder also ensures maximum safety. Both the magazine bit holder and the slimBits that it contains are certified to the international IEC 60900 standard. The slender, 75 mm slimBits ensure perfect access to low-lying screws or spring clips thanks to protective insulation fully integrated into bits in the front section. The twistable cap brings a further advantage, ensuring convenient handling.
6 mm slimBits only to be used in the slimVario® bit holder and slimTorque VDE bit holder (VDE torque system).
Manufactured acc. to IEC 60900.
Content:
- 1x slimBit electric bit TORX® T8 x 75 mm (35506)
- 1x slimBit electric bit TORX® T9 x 75 mm (41160)
- 1x slimBit electric bit TORX® T10 x 75 mm (35507)
- 1x slimBit electric bit TORX® T15 x 75 mm (35508)
- 1x slimBit electric bit TORX® T20 x 75 mm (35509)
- 1x slimBit electric bit TORX® T25 x 75 mm (36071)
Increases your efficiency: Wiha LiftUp electric saves 75% volume and 50% less weight for 100 % efficiency.
Protects your health: No risk of injury, all blades stowed safely inside the handle.
Offers you full protection: Each tool individually tested at 10,000 V AC and approved for 1,000 V AC.
Increases your safety: Wiha slimBits ensure good, protected access to deep-set screws.
Application: Suitable for controlled fastening for live parts up to 1,000 V AC, especially for portable use.
Note: Not for use with bit styles C 6.3 and E 6.3.
Clearly arranged and easy to remove
Saves 75% of space
slimBits allow access to low-lying screws thanks to integrated insulation
Expandable and compatible with EVF products
Safe operation up to 1,000 V AC
The screwdriver with the bit magazine LiftUp electric is the ideal companion for every electrician out on a job. The bit depot hidden in the handle provides space for 6 standard slimBits and extends out of the magazine at the press of a button, making it easy to take out the bits. The time-tested ClicFix holder grips all bits securely and reliably locks them into place. This technology transforms the bit magazine into an all-purpose screwdriver. The magazine bit holder also ensures maximum safety. Both the magazine bit holder and the slimBits that it contains are certified to the international IEC 60900 standard. The slender, 75 mm slimBits ensure perfect access to low-lying screws or spring clips thanks to protective insulation fully integrated into bits in the front section. The twistable cap brings a further advantage, ensuring convenient handling.
6 mm slimBits only to be used in the slimVario® bit holder and slimTorque VDE bit holder (VDE torque system).
Manufactured acc. to IEC 60900.
Content:
- 1x slimBit electric bit Slotted 2.5 mm x 75 mm (34578)
- 1x slimBit electric bit Slotted 3.5 mm x 75 mm (41159)
- 1x slimBit electric bit Slotted 5.5 mm x 75 mm (34581)
- 1x slimBit electric bit Pozidriv PZ1 x 75 mm (34585)
- 1x slimBit electric bit Pozidriv PZ2 x 75 mm (34586)
- 1x slimBit electric bit PlusMinus/Pozidriv SL/PZ2 x 75 mm (34590)
Increases your efficiency: Screwdriver handle size concept for optimal balance between precision and control.
Makes handling easier: Extra-long rotating cap ensures optimum feed.
Increases your efficiency: Careful workmanship and controlled power transmission thanks to the slim handle with soft grip.
The challenge in precision screw fastenings is to work meticulously and carefully without damaging the work piece. Thanks to their long, slim handles and quick-turning zone, Wiha PicoFinish® fine screwdrivers are ideal for delicate and high-precision tasks in precision mechanics as well as for hobbyists and model building. Its ergonomic handle design with a soft zone makes it comfortable to use. The smooth-running rotating cap allows users to turn the screwdriver quickly and sensitively. The printed screwdriver symbols on the rotating cap make it easier to select the right screwdriver profile.
Makes handling easier: Extra-long rotating cap ensures optimum feed.
Increases your efficiency: Screwdriver handle size concept for optimal balance between precision and control.
Increases your efficiency: Careful workmanship and controlled power transmission thanks to the slim handle with soft grip.
Wiha
Increases your efficiency: Integrated powerful LED flashlight.
Saves time: Rapid voltage test thanks to contactless measuring.
Increases your flexibility: The voltage tester covers a large voltage range from 12 - 1,000 V AC.
Increases your efficiency: Compatible for use in all sockets worldwide thanks to measurement tip suited to international usage.
Application: For the detection and localization of live conductors, cable interruptions and cable breaks, blown fuses, defective lamps on light strings, as well as detection of individual wires.
Measuring category: CAT IV 1,000 V
Standards: EPS 22 UKEX 1 333 X, EPS 19 ATEX 1 223 X
Voltage 12 - 1,000 V AC
CAT IV, 1.000 V, ATEX-zertifiziert
One-handed test
5-level optical signal
Switchable acoustic signal
Integrated flashlight function
Prior to the start of electrical installations, electricians must ensure that the work environment is voltage free. A voltage tester is needed for testing alternating electrical fields or detecting potential error sources. Thanks to its optical and acoustic signal, the non-contact Wiha voltage tester indicates whether or not there is any voltage. After switching on, the permanently green illuminated LED indicates readiness. During the voltage test, depending on the strength of the electrical alternating field, the LEDs are illuminated from blue (weak), 'to' orange, to red (strong). Two AAA batteries are required for use, which are included in the scope of delivery. If the device is not in use for 4 minutes, it switches off automatically to save energy. An integrated LED flashlight allows illumination of the measurement site in the dark and can also be used as a flashlight by manually switching it on and off. Thanks to its convenient size the voltage tester with push-on clip fits comfortably in any shirt or pant pocket. With its internationally adjustable measuring tip, the voltage tester is suitable for all outlet variations around the world. The single-pole voltage tester complies with the EN 61010-1 / IEC 61326 standard and is compatible with CAT IV 1,000 VAC. Furthermore,the tool is approved according to the ATEX standard for use in explosive areas (category II). The device should be tested on a known voltage source before and after use to ensure its functionality.
IEC/EN 61010-1, IEC/EN 61326, IP67