Dreusicke offers the fine tools you will need for the maintenance and repair of office machines, computers, electronic and/or fine-mechanical devices. (for commercial users only)
- half-round, long, tapered jaws
- distortion-tolerant, elastic precision tips
- s uitable for finer gripping and cutting work, also on easy and semi-difficult to reach areas
- with cutting edges for soft, medium-hard and hard wire
- cutting edges additionally induction- hardened, cutting edge hardness approx. 61 HRC
- for fine cutting work, e.g. in electronics and fine mechanics
- Load-optimised for a m ore direct feel when working
- sturdy, zero-backlash box joint
- low-friction double spr ing for gentle and even opening
- the polish or mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by peeling chrome from plated tools
- Cutters additionally laser hardened, cutter hardness at least 62 HRC
- High, slim sleeves for fine and comfortable gripping between thumb and index finger
- round head, with small beve l and lead catcher - no uncontrolled loss of cut wire ends
- cutting edge hardness approx. 62 HRC
Knipex
- 35% less effort required than with conventional combination pliers
- with cutting edge s (hardness approx. 63 HRC) for heavy duty
- easier work due to optimised leverage
- eas ier cutting, powerful gripping, bending and pulling
- long cutting edges for thicker cables
- with gripping zones for flat and round material, suitable for versatile use
- Precise, m inimal light gap between the gripping jaws to ensure optimal function of the cutting edges
- c utting edges additionally induction-hardened, cutting edge hardness approx. 63 HRC
Knipex
- for heavy duty use due to wear-resistant gripper jaws
- with gripping zones for flat a nd round material, suitable for versatile use
- with cutting edges for soft, hard and piano wi re
- long cutting edges for thicker cables
- cutting edges additionally induction-harden ed, cutting edge hardness approx. 64 HRC
- particularly wear resistant gripping jaws
- hardness of the gripping jaws approx. 53 HRC
- with precision cutting edges for soft, hard and piano wire
- cuts bolts, nails, rivets , etc. up to Ø 5.2 mm
- efficient joint design ensures exceptional cutting performance with li ttle effort
- cutting edges additionally induction-hardened, cutting edge hardness approx. 64 HRC
- Micro-structured cutting edge reduces slipping of the material from the jaws
- Wit h gripping surface below the joint for gripping and pulling wires from Ø 1.0 mm
- with slim mu lti-component grips without collar for better handling and easier transport
- with large conta ct surface on the handles for better allotment of pressure and more comfort at work
- For reliable tool protection: holding capacity for tools up to 1.5 kg tested in numerous dro p tests
- Reliably prevents the tool falling down, and can protect against serious injuries, d amage to property or loss
- Reduces the risks of tool loss, injury to living beings and damage to objects
- To meet regulations while working at heights, for example industrial climbing, a rborists, rescue services, at sea, etc.
- Diverse attachment options are possible in combinati on with the carabiner and lanyard
- Adapter strap can be attached directly with the cord or th e carabiner to the climbing equipment or fixed points provided for this purpose, quick change of the belay from the tool bag to the tether
- with strap made of a flat belt sewn to one end and a cord and cord stopper sewn into the other end, each sewn four times
- suitable for all KNIPEX pliers with tether attachment point
- No PPE (personal protective equipment): not suitable for personal safety!
- Contents: 2 adapter straps 00 50 01 T, with fixated equipment carabiner 00 50 03 T
Meets your requirements: Yellow hammer head / medium-hard: e.g. for tool and machine engineering, car repairs, sheet metal and assembly work.
Simplifies your work: Makes work easier, optimum impact effect and less effort needed.
Protects your health: Deadblow Hammering without recoil minimises loads on joints, tendons and muscles.
Application: Ideal for delivering measured positioning blows on components such as work pieces in machine vices or for installation work. Medium-hard hammer heads eminently suitable for tool and machine engineering, car repairs as well as sheet metal and assembly work.
Extra: With cast iron balls inside the hammer head for recoilless work.
Choosing the right hammer is particularly important on sensitive surfaces to prevent damage. With its steel tube handle, the no-recoil soft-faced hammer allows the user to deliver measured positioning blows, protecting delicate surfaces and edges through its high-impact effect. Thanks to the special metal filling in the hammer head, the soft-faced hammer also guarantees absolutely no recoil, thus protecting joints. Around 25% more hammer head mass ensures additional power. The yellow medium-hard hammer faces are ideal for universal use in areas such as tool and machine engineering as well as sheet metal and assembly work. The hammer is also impressive due to its steel tube handle with ergonomic, non-slip grip. Each hammer head is available individually as a spare part.
Application: For high torque transfer with small screws, especially when replacing indexable inserts on milling heads.
Application: Chrome-vanadium steel, through-hardened, bronzed.
Extra: Tip diagrams printed to scale.
Extra: Small, robust metal workbench holder to stand on workbench.
Handle: Wiha flag handle.
Blade: Chrome-vanadium steel, through-hardened, bronzed.
Content:
- 1x L-key with flag handle TORX®, black oxidised T6 x 62 mm (03725)
- 1x L-key with flag handle TORX®, black oxidised T7 x 67 mm (03726)
- 1x L-key with flag handle TORX®, black oxidised T8 x 72 mm (03727)
- 1x L-key with flag handle TORX®, black oxidised T9 x 74 mm (03728)
- 1x L-key with flag handle TORX®, black oxidised T10 x 74 mm (03729)
- 1x L-key with flag handle TORX®, black oxidised T15 x 80 mm (03730)
- 1x L-key with flag handle TORX®, black oxidised T20 x 80 mm (03731)
- 1x Workbench stand
Meets your requirements: Black hammer head / medium soft: e.g. for paving, tiling, dry wall construction. Orange hammer head / hard: e.g. for assembly and dismantling work, building and construction work, repair work.
Simplifies your work: Makes work easier, optimum impact effect and less effort needed.
Lowers your costs: Ergonomic hickory wooden handle and hammer head both available as spare parts.
GS tested.