• high transmission ratio for easy cutting
• requires 50 % less effort compared with con ventional combination pliers due to optimised transmission ratio
• solid construction for heav iest strain
• universally applicable
• ergonomically optimised handle shape for firm co ntact to the hand and fatigue reducing operation
• particularly effective cross-hatched knurle d gripping zone in the jaws - for strong gripping and pulling
• additional gripping zone below the joint for powerful leverage and pressing performance
• with cutting edges for soft and ha rd wire
• cutting edges additionally induction-hardened, cutting edge hardness approx. 62 HRC< /li>
• American style
• with fish tape puller in the joint gap
• with universal mandrel crimping point below the joint

• attractive sales packaging with Euro standard perforation
• tools in a plastic deep-dr awn tray with transparent lid
• burnished tip, insulating multi-component handle, VDE-tested
• dimensions (W x H x D): 170 x 370 x 40 mm

• for powerful cutting of larger cross-sections as well as very hard materials
• two-han d operation for maximum cutting force
• 60% less effort required compared to conventional high -leverage diagonal cutters
• 40-fold increase of manual force due to special joint design
• With gripping surface below the joint for gripping and pulling wires from Ø 1.0 mm
• induc tion-hardened precision blades: cutting edge hardness approx. 64 HRC
• blades with recess for easier cutting of round material like hard wires due to better leverage close to the fulcrum

• precision pliers for fine assembly work, e. g. in electronics and fine mechanics
• for gripping, holding and bending
• bolted joint: precise, zero backlash operation of pliers
• precisely finished joint surfaces for smooth, low friction movement along the complete opening r ange
• low-friction double spring for gentle and even opening
• edges carefully deburred
• non-reflective finish
• for very precise assembly work, e.g. in electronics and fine mechanics
• approx. 20% lighter than conventional electronics pliers
• smooth-running do uble spring for a gentle and even opening

• Wire stripper with cable shears - two essential electrical installation tools in one pair of pliers
• Integrated cable shears for the clean cutting of Cu- and Al-cables without crushing up to Ø 15 mm (5 x 2,5 mm²)
• cutting edges additionally induction-hardened, cutting edge hard ness approx. 57 HRC
• Universal adjustment of the stripping blades by means of a knurled screw
• slim dimensions for easy access
• Stripping of single-, multi- and fine stranded cond uctors with plastic or rubber insulation up to Ø 5 mm or 10 mm² cross-section
• Graduated jaw provides a visual orientation aid when stripping wire in standard lengths (11 mm and 16 mm)

• for very tough, continuous use
• high cutting performance with minimum effort due to o ptimum coordination of the cutting edge angle and transmission ratio
• precision cutting edges additionally induction-hardened (cutting edge hardness approx. 64 HRC), for all sorts of wire inclu ding piano wire
• Pliers with integrated, insulated tether attachment point for a tool tether< /li>

• Clever stripping: large capacity range, sharply ground stripping profiles and intuitive posi tioning
• Innovative cutting geometry: easier cutting, especially of flat cables
• Hybri d design: as flat as needle-nose pliers, as wide as combination pliers for high stability with good accessibility
• Precisely ground stripping profiles for solid conductors from 0.75 - 6 mm² and fine-stranded conductors from 0.5 - 4 mm²
• Precise positioning of the wire thanks to locatio n ridges
• Easy cutting of copper and aluminium cables up to Ø 15 mm (1/2")
• Wide, cros s-hatched gripping surfaces for twisting wires
• Milled groove for secure holding and pulling of small work pieces such as nails
• Convex gripping surface on one side for secure gripping o f flat material and gripping area for round material
• Outer edges for deburring pipes

Meets your requirements: For virtually flush cutting of soft copper wires.

Protects your health: Reduces strain from continuous work thanks to opening spring.

Lowers your costs: Electrostatically conductive tools protect electronic components from damage.

Application: Can be used horizontally and virtically.

Application: For virtually flush cutting of soft wires.

Standards: DIN ISO 9654.

IEC 61340-5-1.

Application: For all work with electrostatically endangered components. For outside, inside and depth measurements.

Display: Dial, diameter 35 mm.

Extra: Measurements in ESD protection zones and at ESD workstations.

Extra: Impact resistant dial can be recalibrated to zero.

Material: Surface resistance 10^6 - 10^9 ohms.

Material: Calliper made of ESD-safe material. Non-metallic high-tech material with 60% fibre-glass content.

IEC 61340-5-1.